How To Clean Harman Kardon Aura Studio 2

The Harman Kardon Aura Studio 2 is a pair of loudspeakers that are specifically designed for home theater use. They are available in either Black Walnut or Ebony finishes and come with two different grills, one more contemporary and the other more classic. A set of five-inch woofers and fifteen-inch subwoofers offer high-quality sound reproduction. So now the question is How To Clean Harman Kardon Aura Studio 2?? 

How To Clean Harman Kardon Aura Studio 2

To recreate the sound, the surface is similarly rotated while a playback stylus traces the groove and is therefore vibrated by it, very faintly reproducing the recorded signal. The tracing is continued until the stylus reaches the end of the groove, whereupon it ascends to the upper surface and continues to trace the next succeeding groove. 

This movement from one groove to another is called a “mechanical scan.” In some cases, the stylus will pick up so much vibration from the surface as to reproduce not only the groove but also the surrounding surfaces. This causes a hissing or crackling sound which is very irritating to the listener. 

In contrast to the previous models, the new models do not have a plastic front panel. If you need to clean your Harman Kardon aura studio 2, you must first know which parts of the keyboard are made of plastic and which ones are metal. 

This is important because the cleaning of the Harman Kardon aura studio 2 is done by rubbing with a special abrasive and alcohol mixture that is used only on the parts of the keyboard that are made of plastic.

Later, the keyboard will be dried in warm water. Only the keys that are made of metal can be cleaned with a damp cloth. The cleaning process is usually performed by a technician, since the manual cleaning procedure may damage the keyboard. 

Because for the good sound you need to clean it properly. The cleaning of the Harman Kardon aura studio 2 consists of three stages: first, the keyboard must be dried, then the plastic parts must be cleaned, followed by the metal parts.

Now remove the paper ball from the alcohol and place it on the surface of the keyboard. Rub the alcohol-soaked paper ball around the entire keyboard in an even manner. When you have completed this step, the entire keyboard will be coated with a thin layer of alcohol. 

Do not worry if the paper ball gets onto the printed characters or other non-plastic parts of your keyboard; just rub it off. Next, remove another handful of balls of paper and soak them in alcohol.

Also Read: IROBOT ROOMBA 761 REVIEW (THE ULTIMATE CLEANING MACHINE)

Later, pour out the alcohol from these papers and replace them on the keyboard. Continue to do this until all the keyboard is covered with paper balls that have been soaked in alcohol. Now put some abrasive on a separate piece of paper and rub it over the entire keyboard. The abrasive will remove the plastic parts of the keyboard. 

You can use a coin or similar object to rub over the keyboard if you do not have an abrasive. After rubbing, the keyboard should be dried with a clean, soft cloth. After that, the entire keyboard must be cleaned with a damp cloth. Only then may it be used again. 

By the way, when cleaning the metal keys, it is important that you only use alcohol and no solvents whatsoever. Even a trace of oil may prevent the keys from working properly. Indeed, the oil may cause the key to “stick.” Indeed, the specialist will even show you how to make it.

Again, take a few sheets of paper and crumple them up into a ball. Then put some rubbing alcohol on the ball of paper and squeeze it until the alcohol has soaked into the paper. Next, remove the paper ball from the alcohol and place it on the surface of the keyboard. Rub the alcohol-soaked paper ball around the entire keyboard in an even manner. When you have completed this step, the entire keyboard will be coated with a thin layer of alcohol. Do not worry if the paper ball gets onto the printed characters or other non-plastic parts of your keyboard; just rub it off. 

Next, remove another handful of balls of paper and soak them in alcohol. Later, pour out the alcohol from these papers and replace them on the keyboard. Continue to do this until all the keyboard is covered with paper balls that have been soaked in alcohol. Now put some abrasive on a separate piece of paper and rub it over the entire keyboard. The abrasive will remove the plastic parts of the keyboard.

That is all there is to it. The cleaning of the Harman Kardon aura studio 2 consists of three stages: first, the keyboard must be dried, then the plastic parts must be cleaned, followed by the metal parts. 

For this, the keyboard must be placed on a table, and alcohol and an abrasive must be poured into the keyboard from one side so that the alcohol collects in the lower area and the abrasive in the upper area. Indeed, the specialist will even show you how to make it. First, take a few sheets of paper and crumple them up into a ball. 

Then put some rubbing alcohol on the ball of paper and squeeze it until the alcohol has soaked into the paper. Next, remove the paper ball from the alcohol and place it on the surface of the keyboard. Rub the alcohol-soaked paper ball around the entire keyboard in an even manner. When you have completed this step, the entire keyboard will be coated with a thin layer of alcohol.

In conclusion, it is important to keep your Harman Kardon Aura Studio 2 clean. By doing this, you are guaranteeing that the sound quality will not be compromised. There are various ways to clean your Harman Kardon Aura Studio 2, but it is best to use a damp fabric or take it apart for in-depth cleaning.

Leave a Reply

shares