How to use a wet tile saw

Milano 1200PRO 2000W 305mm (12") Wet Tile Saw

Sometimes it is not advisable to go for professional tile setters, yet you can do it yourself. You only need to know how to use a wet tile to have your tile cutting projects done correctly. 

When you handle the tool with great care, you may produce smooth and clean tile cuts for your DIY project. More so, a wet tile saw can make straight tile cuts and much suitable for cutting bevels, odd angles, and small shapes.

Unlike snap cutters, a wet tile can leave you with uniform and smooth cuts. Make this guide useful on how to operate the machine for making perfect tile cuts.

What is a wet tile saw?

A wet tile saw is a powerful tool for cutting tiles that resemble a miter or table saw with a diamond-edged carbide blade. Cooling the edge enables the agency to efficiently and safely grind or cut ceramic, porcelain, or stone tiles to your desires size. 

This type of tile cutter features a sliding table in charge of feeding tiles to the overhead blade. If you use the machine safely and carefully, you may get clean tile cuts of your specifications.

How to use a wet tile saw steps by steps guide 

A wet tile saw under $300 uses electricity for its operations, and therefore you should know how it works. Below is a step-by-step guide on how you can achieve the best results.

Step 1: Preparing your working area

I hope you know using a wet saw may spread water all over your working area. It is advisable to work from a garage or in an open place where water spraying will not mess. 

And if you decide to use the tool in your small spaced-room working area, you have to cover your floor or other nearby surfaces with either a plastic material to avoid overspray.

Don’t forget to choose a work area with a water outlet. Also, ensure that there is a stable, sturdy work surface for the stability of the saw. You may use a picnic table or a portable workbench to support the base of the machine. 

However, some people prefer placing the wet tile saw on the concrete slab or flat ground. If your device needs a constant water supply, you will have to install the hose spigot.

Step 2: Safety measures

A wet tile saw has a rotating blade that might be dangerous if you fail to handle the tool with great care. Therefore, you should use the wet saw with caution. Using the equipment needs excellent attention due to the combination of electricity and water. You may also revise the machine’s safety instructions from the company before using it.

Some of the safety measurements required to adhere include; wearing safety goggles for eye protection, hearing protectors, work boots, vinyl gloves, and an apron. 

Tiles have sharp edges that can pose health complications to you. More so, the machine produces a loud sound that can interfere with your hearing, the need for hearing protectors.

Step 3: Preparing the tool

Under this step, you need to fill the saw’s reservoir with enough water. When filling the pool, ensure that the water level covers its recirculation pump level. If you choose to use freshwater, you will have to set up a hose model directly connecting to the machine from a fixture. 

Connect your tool to a protected GFCI outlet or an extended GFCI cord. GFCI is essential when mixing electricity and water. It would help if you also made sure that there is a safe drip loop in the line leaving the machine to the outlet.

Step 4: Drawing a cut line

It would help if you did not jump into cutting the tiles without line marks. Marking the tiles will enable you to produce accurate shapes than cutting without effects. I can suggest using a pencil or any inedible marking from drawing your desires’ profiles on the tile under this step. 

Furthermore, ensure that the cutline is as straight and narrow as possible. You can also use other materials such as measuring tapes, pencil compass, scales, etc. for making well-defined angles and edges.

 

Step 5: Turn ON the water switch

After you are through with the above steps, it is now time to turn on the water switch. Immediately after doing so, you will see water flowing smoothly around the rotating blade’s edges. The sword begins at a low speed to the highest. Moderate the rate of water not to break the tile or the sword.

Step 6: inserting the tile

After identifying the cut lines and measurements, the next thing is to lock the plate using the measurement guides. It would help if you were careful while placing the tiles on the measured-plate. 

Remember, you can locate the tile on any blade’s side based on your ease or comfort of working. After placing the tile, lock it by lowering the level

Step 7: Power ON the saw

Tap the ON/OFF button of the tool to switch it ON. You should avoid touching the switch with damp hands. There is not much about this step rather than powering ON your instrument.

Step 8: Moving your tile

Here, you will have to push the tile at the speed of your desires. The rotating blade is always stationary, and therefore it is you to increase or reduce the rate of tile cutting. But don’t force the tile; you may break it or the blade of the saw. More so, use your hands to hold the tile’s sides while cutting; if the sides are not tiny. If the sides are small, don’t risk; you may end up with fewer fingers.

Frequently asked questions

What are the safety measures before using the wet tile saw?

Wear safety goggles for eye protection, hearing protectors, work boots, vinyl gloves, and an apron.

Can I fill the reservoir of a wet tile saw with dirty water?

Yes, but is it healthy for you? I prefer using fresh water for your safety too.

Conclusion

A wet tile saw remains an essential tool for cutting hard materials, dense and smooth shapes. If you are a tile setter, then you should know how to use a wet tile saw before purchasing one. 

Working with such equipment is exciting as it uses a water reservoir for soaking the blade while cutting tiles. This art enables the edge to run smoothly and reduces the chances of wear and dust. 

Cooling also prevents the blade from melting under a lot of heat. Moreover, you may decide to set up your model using an electric pump and a reservoir. Also visit horizoninternational.co.nz for best experience. 

Leave a Reply

shares